Pneumatic regulating butterfly valve
- sell:021-32051999
- sell:021-32050777
- fax:021-66099555
Details
- Product Introduction
- Service Promise
- Ordering Process
ZMAW pneumatic membrane control butterfly valve / ZSRW, ZSCW pneumatic piston control butterfly valve input control signal (4-20mADC or 1-5VDC) air source can control operation, simple and compact structure, easy to manufacture large diameter, with self-cleaning effect, small resistance coefficient, large flow capacity. It is suitable for the regulation of suspended solids and strong and turbid slurry fluids. Clean medium, can choose the valve plate plus soft seal (rubber ring, tetrafluoro ring) to reduce leakage (up to 0.01%), high temperature and high pressure can choose the three eccentric hard seal valve body. The order must be marked.
Main technical parameters of pneumatic regulating butterfly valve
Nominal path mm | 50 | 80 | 100 | 125 | 150 | 200 | 250 | 300 | 350 | 400 | 450 | 500 | 600 | 700 | 800 | 900 | 1000 | |
Rated discharge coefficient Kv | 85 | 220 | 340 | 530 | 770 | 1360 | 2130 | 3060 | 4160 | 5450 | 6900 | 8500 | 12200 | 16600 | 21700 | 27540 | 34000 | |
Nominal pressure MPa | 0.6 | |||||||||||||||||
Rated turning angle ° | 70 | |||||||||||||||||
Signal pressure KPa | 20~100 | |||||||||||||||||
Flow characteristics | 近似等百分比 | |||||||||||||||||
Medium temperature ℃ | -20~200(常温) ; -40~450(中温) ; -40~600(高温) | |||||||||||||||||
Nozzle flange | 按JB78-59对夹式法兰连接 | |||||||||||||||||
Signal connection screw hole | M16×1.5 | |||||||||||||||||
Matching actuator | Thin film | ZMA-2 | ZMA-3 | ZMA-4 | ZMA-5 | |||||||||||||
Piston type | ZSC-45 | |||||||||||||||||
body material | ZG230-450;1Cr18Ni9; ZG1Cr18Ni9Ti、ZGOCr18Ni12Mo2Ti | |||||||||||||||||
Appendable appendage | Handwheel, locator, air filter and pressure reducer. |
Part name | Material Science | Temperature range C |
Body valve plate | ZG230-450 | -40-450 |
ZG1Cr18Ni9Ti | -250-550 | |
ZG0Cr18Ni12Mo2Ti |
Note: This table is the limit service temperature of all kinds of materials. In actual selection, the lowest and highest service temperature of materials should be determined according to the medium temperature range of the products. The lowest service temperature should not be lower than the lower limit of the medium temperature range, and the highest service temperature should not be higher than the upper limit of the medium temperature range.
Main technical parameters of pneumatic regulating butterfly valve thin film actuator
Model | ZMA-2 | ZMA-3 | ZMA-4 | ZMA-5 |
effective area cm2 | 280 | 400 | 630 | 1000 |
Trip mm | 16 | 25 | 40 | 60 |
Spring range KPa | 20~100 ; 40~200 ; 20~60 ; 60~100 |
Model | Piston diameter mm | effective area cm2 | Maximum stroke mm | Maximum operating pressure KPa | Maximum output force N |
ZSC-45 | 250 | 484 | 60 | 500 | 21800 |
Executing agency | Thin film actuator | Piston actuator | |||||
Category | Without locator | Belt locator | Belt locator | ||||
Spring range KPa | |||||||
20~100 40~200 | 20~60 60~100 | ||||||
Project | Basic error% | ±8 | - | ±2.0 | ±2.0 | ||
Difference% | 6 | - | 2.0 | 2.0 | |||
Dead zone% | 5 | - | 0.8 | 0.8 | |||
Always point deviation%. | Air opening | Starting point | ±4.0 | ±4.0 | ±2.0 | ± | |
End | ±8 | ±8 | |||||
Gas pass | Starting point | ±8 | ±8 | ||||
End | ±4.0 | ±4.0 | |||||
Rated angle deviation% | ±2.5 | ||||||
Allowable leakage 1/h | Rated capacity of 2 * 10-2 * valves |
Matching actuator type | ZMA-2 | ZMA-3 | ZMA-4 | ZMA-5 | ZSC-45 | ||||||
0° | 70° | 0° | 70° | 0° | 70° | 0° | 70° | 0° | 70° | ||
Nominal path mm | 50 | 0.6 | 0.097 (0.22) | ||||||||
80 | 0.6 | 0.038 (0.086) | |||||||||
100 | 0.556 (0.6) | 0.0196 (0.0445) | |||||||||
125 | 0.6 | 0.0250 (0.0542) | |||||||||
150 | 0.444 (0.6) | 0.0150 (0.0314) | |||||||||
200 | 0.185 (0.407) | 0.00587 (0.0129) | |||||||||
250 | 0.331 (0.6) | 0.00845 (0.0175) | |||||||||
300 | 0.181 (0.385) | 0.00461 (0.00983) | |||||||||
350 | 0.133 (0.284) | 0.00292 (0.00622) | |||||||||
400 | 0.216 (0.45) | 0.00485 (0.0101) | |||||||||
450 | 0.171 (0.356) | 0.00341 (0.00741) | |||||||||
500 | 0.139 (0.289) | 0.0025 (0.0052) | |||||||||
600 | 0.6 | 0.019 | |||||||||
700 | 0.6 | 0.0119 | |||||||||
800 | 0.442 | 0.00795 | |||||||||
900 | 0.339 | 0.00599 | |||||||||
1000 | 0.236 | 0.00403 |
Note: the values in brackets are allowable pressure differences with positioners.
Main size of pneumatic regulating butterfly valve
ZMAW pneumatic thin film adjusting butterfly valve
公称通径 | D1 | D2 | L1 | L2 | n-d | H | H1 | H2 | D | L3 | 法兰端面距 |
50 | 110 | 92 | 200 | 4-14 | 637 | 582 | 382 | 280 | 278 | 60 | |
80 | 150 | 125 | 92 | 200 | 4-18 | 644 | 582 | 382 | 280 | 278 | |
100 | 175 | 145 | 102 | 210 | 654 | 280 | 278 | ||||
125 | 200 | 175 | 117 | 234 | 8-18 | 723 | 636 | 436 | 325 | 278 | |
150 | 225 | 200 | 130 | 247 | 736 | 325 | 278 | ||||
200 | 280 | 255 | 172 | 287 | 763 | 325 | 278 | 70 | |||
250 | 335 | 310 | 197 | 327 | 12-18 | 1008 | 853 | 615 | 410 | 376 | |
300 | 395 | 362 | 227 | 351 | 12-23 | 1034 | 410 | 376 | 80 | ||
350 | 445 | 412 | 252 | 376 | 1059 | 410 | 376 | ||||
400 | 495 | 462 | 296 | 432 | 16-23 | 1238 | 1007 | 720 | 495 | 376 | 100 |
450 | 550 | 518 | 321 | 459 | 1266 | 495 | 376 | ||||
500 | 600 | 568 | 346 | 484 | 1291 | 495 | 376 | ||||
600 | 705 | 755 | 480 | 565 | 20-25 | 1486 | 1109 | 796 | 180 | 150 | |
700 | 810 | 860 | 530 | 615 | 24-25 | 1539 | 180 | ||||
800 | 920 | 975 | 595 | 675 | 24-30 | 1596 | 180 | 200 | |||
900 | 1020 | 1075 | 685 | 770 | 24-30 | 1661 | 1124 | 180 | |||
1000 | 1120 | 1175 | 735 | 810 | 28-30 | 1711 | 1124 | 180 | 200 |
Nominal pathDN | Structure length (standard value) | Connection size | |||||||||
L | H | H1 | PN0.6MPa | PN1.0MPa | |||||||
mm | inch | Flanged | Pair clip | D | D1 | Z-d | D | D2 | Z-d | ||
50 | 2 | 108 | 43 | 100 | 400 | 140 | 110 | 4--14 | 165 | 125 | 4--18 |
65 | 21/2 | 112 | 46 | 115 | 420 | 160 | 130 | 4--14 | 185 | 145 | 4--18 |
80 | 3 | 114 | 49 | 120 | 138 | 190 | 150 | 4--18 | 200 | 160 | 8-18 |
100 | 4 | 127 | 56 | 130 | 524 | 210 | 170 | 4--18 | 220 | 180 | 8-18 |
125 | 5 | 140 | 64 | 150 | 570 | 240 | 200 | 8-18 | 250 | 210 | 8-18 |
150 | 6 | 140 | 70 | 170 | 743 | 265 | 225 | 8-18 | 285 | 240 | 8-22 |
200 | 8 | 152 | 76 | 200 | 767 | 320 | 280 | 8-18 | 340 | 295 | 8-22 |
250 | 10 | 165 | 76 | 235 | 790 | 375 | 335 | 12-18 | 395 | 350 | 12-22 |
300 | 12 | 178 | 83 | 300 | 890 | 440 | 395 | 12-22 | 445 | 400 | 12-22 |
350 | 14 | 190 | 92 | 325 | 954 | 490 | 445 | 16-22 | 505 | 460 | 16-22 |
400 | 16 | 216 | 102 | 355 | 1070 | 540 | 495 | 16-22 | 565 | 515 | 16-26 |
450 | 18 | 222 | 114 | 390 | 1140 | 595 | 550 | 20-22 | 615 | 565 | 20-26 |
500 | 20 | 229 | 127 | 420 | 1200 | 645 | 600 | 20-26 | 670 | 620 | 20-26 |
600 | 24 | 267 | 154 | 490 | 1380 | 755 | 705 | 24--26 | 780 | 725 | 20-30 |
700 | 28 | 292 | 165 | 550 | 1580 | 860 | 810 | 24--30 | 895 | 840 | 24--30 |
800 | 32 | 318 | 190 | 640 | 1760 | 975 | 920 | 24--30 | 1015 | 950 | 24--33 |
900 | 36 | 330 | 203 | 710 | 1075 | 1020 | 24--30 | 1115 | 1050 | 28-33 | |
1000 | 40 | 410 | 216 | 770 | 1175 | 1120 | 28--30 | 1230 | 1160 | 28-36 | |
1200 | 48 | 470 | 254 | 890 | 1405 | 1340 | 32-33 | 1450 | 1380 | 32-39 |
The best quality, first-class service Qigao creates more value for you!
"Qigao Valve" expects to continuously improve service quality and strive for excellence. "Sincere service" is the eternal theme of "Qigao". "Qigao" strictly followsIS09001-2000 Quality system certification requirements, strict quality control, responsibility to people, to ensure the healthy operation of production, sales and service. Strengthen communication with users and provide quality products to our customers with perfection and perfect service. Hereby our factory makes the following commitments:
Product Standards:
Products in strict accordance with ChinaGB、HG Standard and USAPISuch as standard design, manufacturing, acceptance. The hardness of the sealing surface meets the requirements of the state and the width exceeds the national standard.
pre-sale service:
Product introduction, technical exchange, non-standard product design, troubleshooting。
Sale service:
A trustworthy contract guarantees timely delivery and keeps in touch with customers. For special or duplicate products, our factory arranges technicians to use and troubleshoot the products for users.
After sales service:
1、"Qigao" brand product quality period is from the factory12In the month, the implementation of the "three guarantees" service (return, replacement, warranty).
2、During the use of our products, our factory regularly organizes technical and quality inspection personnel to visit and consult users for feedback on product quality, usage status and improvement opinions, so as to further improve product quality.
3、Respond quickly to the quality of user complaints, after-sales service personnel rushed to the scene in 24-36 hours (48 hours outside the province).
4、For after-sales service, users are required to fill out the quality feedback information form after the service and make an appraisal opinion in order to improve the service quality of Qigao.
1、If the customer has special requirements for the product, the following instructions must be provided in the order contract.:
a、Structure length;
b、Connection Type;
c、Nominal diameter, full diameter, reduced diameter, pipe size;
d、Operating medium and temperature, pressure range;
e、Tests, inspection standards and other requirements
2、The factory can configure various types of driving devices according to customer's specific requirements.。
3、If the type and model of the valve are determined by the customer, the customer shall correctly state the meaning and requirements of the model and sign the contract under the condition that the supplier and the buyer understand each other.
4、For futures and order customers, please call us in advance to tell the required valve model, specification, quantity, delivery time and location, and timely transfer to the factory account according to the total 30% deposit or full payment. The rest of the payment is pending. Import before shipment to arrange delivery in time.
Order Process:
1、Customer purchase list fax to021-33872143,Or call us 021-33872141
2、Receive customer purchase list, provide valve model selection and quotation (price list)。
3、Specific agreement: delivery date, special requirements, etc.。
download Google:
1、If the customer has special requirements for the product, the following instructions must be provided in the order contract.:
|
|||||
|
|||||
2、The factory can configure various types of driving devices according to customer's specific requirements.。
|
|||||
3、If the type and model of the valve are determined by the customer, the customer shall correctly state the meaning and requirements of the model and sign the contract under the condition that the supplier and the buyer understand each other.
|
|||||
4、For futures and order customers, please call us first to tell the required valve model, specifications, quantity, delivery time and location, and press the total30%The deposit or full payment will be remitted to our factory account in time., The rest of the payment will be remitted before shipment to arrange delivery in time.。
|
Sale service:
Trustworthy contract, guarantee timely delivery, keep in touch with customers at any time。
For special or duplicate products, our factory arranges technicians to use and troubleshoot the products for users.
After sales service:
1、"Qigao" product quality period is from the factory12Month, practice“Three packs”Service (return, replacement, warranty)。
2、During the use of our products, our factory regularly organizes technical and quality inspection personnel to visit and consult users for feedback on product quality, usage status and improvement opinions.,
In order to further improve product quality。
3、Respond quickly to the quality of user complaints, after-sales service personnel24-36Hours (outside the province48Hour) rushed to the scene。
4、For after-sales service, the user is required to fill out the quality feedback information form after the service and make an appraisal opinion in order to improve the service quality of “Qigao”.。
statement |
|